log in | register | forums
Show:
Go:
Forums
Username:

Password:

User accounts
Register new account
Forgot password
Forum stats
List of members
Search the forums

Advanced search
Recent discussions
- WROCC Newsletter Volume 41:11 reviewed (News:)
- WROCC March 2024 meeting o... Hughes and Peter Richmond (News:1)
- Rougol March 2024 meeting on monday with Bernard Boase (News:)
- Drag'n'Drop 13i2 edition reviewed (News:)
- South-West Show 2024 talks (News:4)
- February 2024 News Summary (News:1)
- Next developer fireside chat (News:)
- DDE31d released (News:)
- South-West Show 2024 Report (News:)
- South-West Show 2024 in pictures (News:)
Latest postings RSS Feeds
RSS 2.0 | 1.0 | 0.9
Atom 0.3
Misc RDF | CDF
 
View on Mastodon
@www.iconbar.com@rss-parrot.net
Site Search
 
Article archives
Acorn Arcade forums: General: revive a410/1 - can anyone advise?
 
  revive a410/1 - can anyone advise?
  tfoster60 (22:26 16/4/2014)
  Michael Foot (03:53 17/4/2014)
  sirbod (07:00 17/4/2014)
    PaulV (09:42 17/4/2014)
  helpful (09:39 17/4/2014)
 
Terry Foster Message #123193, posted by tfoster60 at 22:26, 16/4/2014
Member
Posts: 1
I have looked out the rubbish in the roof and come across my old Archimedes A410/1 machine.

I plugged it in and whilst the monitor works, the rest of the machine appears dead.

I have checked the power supply and I am getting 12v AND 5V feeds from the PSU so it should be fine.

Someone once took the machine if I remember rightly and I am wondering if a wrong keyboard could have damaged the motherboard?

Other than that - it has been 15 years since it was last powered up )no batteries were left in it) so could it be that the ROM has somehow discharged?

I say it has been in the roof, but it is not hot up there as it was converted ages ago. I press reset on the keyboard and it flashes the three leds on the caps, scroll and num locks but otherwise it is lifeless when I press these keys.

I have a 20Mb hard drive on there with some games I would not have mind revisiting, but otherwise would anyone in this group know if this can be revived or if it's going to end up at the recycling centre down the road. I'd love to revive it - even with Raspberry Pi if needed but I have not got the know how to do that.

Any advice would be received gratefully and I thank everyone who replies in advance.

Terry
  ^[ Log in to reply ]
 
Michael Foot Message #123194, posted by Michael Foot at 03:53, 17/4/2014, in reply to message #123193
AA refugee
Posts: 25
If the machine has no batteries, the CMOS settings will be unset.
Holding down the Del key when you power it on will reset the CMOS and hopefully the machine will burst into life.
If the machine has not been covered when stored, it would pay to take the top off and clean out any foreign objects too.
I'm sure someone on here will take it off your hands if it's not in a good way.

[Edited by Michael Foot at 04:53, 17/4/2014]
  ^[ Log in to reply ]
 
Jon Abbott Message #123195, posted by sirbod at 07:00, 17/4/2014, in reply to message #123193
Member
Posts: 563
Try pulling the 12v line off the mobo and see if you get lights/fan at power on, if you do take a look at this thread for ths fix.
  ^[ Log in to reply ]
 
Bryan Hogan Message #123197, posted by helpful at 09:39, 17/4/2014, in reply to message #123193
Member
Posts: 249
If there is a hardware fault the issue might be flashed out as a binary code on the floppy drive light. Check that just after turning it on and enter them here:

http://www.retro-kit.co.uk/page.cfm/content/Common-RISC-OS-POST-failure-errors/

Where are you located, in case someone is nearby who can assist?
  ^[ Log in to reply ]
 
Paul Vernon Message #123198, posted by PaulV at 09:42, 17/4/2014, in reply to message #123195
Member
Posts: 135
The link Jon has pointed out works great for A300 and A400 series machines but the A400/1 series has different component numbering so although removing/replacing the 12V decoupling capacitor is the most likely answer, in the 400/1 series, it's not C37 as stated in that thread...

In the 400/1 series it's C53 which is the 12V decoupling cap.

Interestingly in the 300 and 400 series the cap is rated at 100uF 16V in the 400/1 it's a 100uF 25V component which AFAIK is much more reliable on the 12V line because it's got much more capacity to absorb voltage spikes at power on etc.

Paul
  ^[ Log in to reply ]
 

Acorn Arcade forums: General: revive a410/1 - can anyone advise?